Membuat VOIP Pada Cisco Packet Tracer
Membuat
VOIP pada Cisco Packet Tracer
Yang harus dilakukan pertama adalah :
1.setting switchport voice
2. konfigurasi interface secara static pada router
3. konfigurasi interface host secara auto (DHCP)
4. setting voip pada router
5. setting dial number untuk ipPhone
Ok langsung saja, kita praktekan !
1. buka
software cisco paket tracer
2. buat sebuah router jenis 2811, pastikan untuk
memilih router ini, karena hanya jenis ini yang menyediakan fungsi untuk
ipPhone
3. buat sebuah switch, switch yang saya gunakan
adalah switch jenis 2960
4. buat 3 atau 4 buah ipPhone, saya menggunakan 3
ipPhone
5. sambungkan seluruh ipPhone ke switch, dan switch
ke router masing-masing menggunakan kabel jenis straight-throug
6. colokkan power adapter pada setiap ipPhone klik
pada ipPhone kemudian drag power ke portnya.
# Selanjutnya kita masuk pada tahap konfigurasi
switch, pada CLI
ketikan
perintah-perintah sebagai berikut :
Switch>en
Switch#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int range fa0/1-24
Switch(config-if-range)#switchport voice vlan 1
Switch(config-if-range)#exit
Switch(config)#
Switch#
%SYS-5-CONFIG_I: Configured from console by console
Switch#
#Selanjutnya kita akan masuk ke tahap konfigurasi
router.
Pada tahap ini sama kita masuk ke CLI lalu
ketikan perintah-perintah seperti di bawah ini :
--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: n
Press RETURN to get started!
Router>en
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip dhcp pool voice
Router(dhcp-config)#network 192.168.1.0
255.255.255.0
Router(dhcp-config)#default-router 192.168.1.34
Router(dhcp-config)#option 150 ip 192.168.1.34
Router(dhcp-config)#exit
Router(config)#ip dhcp excluded-address 192.168.1.34
Router(config)#int fastethernet 0/0
Router(config-if)#ip address 192.168.1.34
255.255.255.0
Router(config-if)#no shutdown
%LINK-5-CHANGED: Interface FastEthernet0/0, changed
state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#telephony-service
Router(config-telephony)#max-ephones 3
Router(config-telephony)#max-dn 3
Router(config-telephony)#ip source-address
192.168.1.34 port 2000
Router(config-telephony)#auto assign 4 to 6
Router(config-telephony)#auto assign 1 to 5
Router(config-telephony)#exit
Router(config)#ephone-dn 1
Router(config-ephone-dn)#%LINK-3-UPDOWN: Interface
ephone_dsp DN 1.1, changed state to up
Router(config-ephone-dn)#number 132131
Router(config-ephone-dn)#ephone-dn 2
%LINK-3-UPDOWN: Interface ephone_dsp DN 2.1, changed
state to up
Router(config-ephone-dn)#
Router(config-ephone-dn)#number 132132
Router(config-ephone-dn)#ephone-dn 3
Router(config-ephone-dn)#%LINK-3-UPDOWN: Interface
ephone_dsp DN 3.1, changed state to up
Router(config-ephone-dn)#number 132133
Router(config-ephone-dn)#
NB
: pada saat mengetikan ephone-dn 1
sampai ephone-dn 3 tekan enter 2 kali
"ephone-dn
1"
kemudian
tekan enter 2 kali
Sekarang kita akan test koneksi dengan dial number
Dial number yang saya gunakan adalah nomor NISN saya
yaitu 132131
Saya mencoba padaipPhone 3 dengan dial number 132133
Dia akan menuju ke number 132132 (pada ipPhone 2)
Kemudian pada ipPhone 2 sudah terdeteksi artinya
kita berhasil karena ada keterangan connected
Itulah sedikit langkah-langkah membuat VoIp pada
Cisco Paket Tracer .
Semoga bermanfaat J
thank ya avianyye ........ good job ............!!!!!!
ReplyDeleteok youre welcome ;)
DeleteThis comment has been removed by a blog administrator.
ReplyDelete:v
Delete